DS411slim Ethernet prob or hang? Flash Dump?

Questions and mods regarding system management may go here
Forum rules
1) This is a user forum for Synology users to share experience/help out each other: if you need direct assistance from the Synology technical support team, please use the following form:

https://account.synology.com/support/support_form.php?lang=enu



2) To avoid putting users' DiskStation at risk, please don't paste links to any patches provided by our Support team as we will systematically remove them. Our Support team will provide the correct patch for your DiskStation model.
porterLv
I'm New!
I'm New!
Posts: 1
Joined: Mon Mar 27, 2017 2:22 pm

DS411slim Ethernet prob or hang? Flash Dump?

Postby porterLv » Mon Mar 27, 2017 3:12 pm

Hello. Need help.
My NAS is: Synology DS411slim S/N. mod not: serial# removed MAC:0011322A0DA7
Board; ADM41L1 Ver 1.3 (P/N 08-06ADM4113) + on label "1922".

Marvell>> version
U-Boot 1.1.4 (Aug 9 2010 - 19:58:12) Marvell version: 3.5.3

I got device in not working condition, do`n know it history.CPU Core VRM was burned out (ZT7184).After DC-DC resolding CPU voltage is normal.
NAS can Boot but still not available on LAN. In attachment You find full bootlog from terminal (no HDD connected in all LOG. Log via UART terminal (JP1)).
Log (No Ethernet cable connected):

Code: Select all

         __  __                      _ _
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
 \___/    |____/ \___/ \___/ \__|  ** LOADER **
 ** MARVELL BOARD: Synology Disk Station LE

U-Boot 1.1.4 (Aug  9 2010 - 19:58:12) Marvell version: 3.5.3

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 0068B3D4

Soc: MV88F6282 Rev 1CPU running @ 1500Mhz L2 running @ 500Mhz
SysClock = 500Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000   size 256MB
DRAM Total size 256MB  16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Using default environment

[4096kB@f8000000] Flash:  4 MB

CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
PEX 1: interface detected no Link.

Synology Model: DS411slim
Fan Status: Good

Net:   egiga0 [PRIME], egiga1
Hit any key to stop autoboot:  0
## Booting image at f8080000 ...
   Image Name:   Linux-2.6.32.12
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1552152 Bytes =  1.5 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK
## Loading Ramdisk Image at f8280000 ...
   Image Name:   synology_88f6282_411slim 8451
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    1030907 Bytes = 1006.7 kB
   Load Address: 00800000
   Entry Point:  00800000
   Verifying Checksum ... OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000] Linux version 2.6.32.12 (root@build4) (gcc version 4.6.4 (Marvell GCC release 20150204-c4af733b 64K MAXPAGESIZE ALIGN CVE-2015-0235) ) #8451 Wed Aug 17 05:12:01 CST 2016
[    0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
[    0.000000] CPU: VIVT data cache, VIVT instruction cache
[    0.000000] Machine: Synology 6282 board
[    0.000000] Using UBoot passing parameters structure
[    0.000000] Sys Clk = 200000000, Tclk = 166666667
[    0.000000] Synology Board ID: 24
[    0.000000] Memory policy: ECC disabled, Data cache writeback
[    0.000000] Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 65024
[    0.000000] Kernel command line: console=ttyS0,115200 ip=off initrd=0x00800040,4M root=/dev/md0 rw syno_hw_version=DS411slimv10 ihd_num=0 netif_num=1
[    0.000000] Synology Hardware Version: DS411slimv10-j
[    0.000000] Internal HD num: 0
[    0.000000] Internal netif num: 1
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Memory: 256MB = 256MB total
[    0.000000] Memory: 244992KB available (3652K code, 519K data, 124K init, 0K highmem)
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:128
[    0.000000] Console: colour dummy device 80x30
[    0.000000] Calibrating delay loop... 1490.94 BogoMIPS (lpj=7454720)
[    0.240000] Mount-cache hash table entries: 512
[    0.240000] CPU: Testing write buffer coherency: ok
[    0.240000] devtmpfs: initialized
[    0.240000] xor: measuring software checksum speed
[    0.290000]    arm4regs  :  1358.000 MB/sec
[    0.340000]    8regs     :   814.800 MB/sec
[    0.390000]    32regs    :  1051.600 MB/sec
[    0.390000] xor: using function: arm4regs (1358.000 MB/sec)
[    0.390000] NET: Registered protocol family 16
[    0.390000] Feroceon L2: Enabling L2
[    0.390000] Feroceon L2: Cache support initialised, in WT override mode.
[    0.410000]
[    0.410000] CPU Interface
[    0.410000] -------------
[    0.410000] SDRAM_CS0 ....base 00000000, size 256MB
[    0.410000] SDRAM_CS1 ....disable
[    0.410000] SDRAM_CS2 ....disable
[    0.410000] SDRAM_CS3 ....disable
[    0.410000] PEX0_MEM ....base e0000000, size 128MB
[    0.410000] PEX0_IO ....base f2000000, size   1MB
[    0.410000] PEX1_MEM ....base e8000000, size 128MB
[    0.410000] PEX1_IO ....base f2100000, size   1MB
[    0.410000] INTER_REGS ....base f1000000, size   1MB
[    0.410000] NFLASH_CS ....base fa000000, size   2MB
[    0.410000] SPI_CS ....base f4000000, size  16MB
[    0.410000] BOOT_ROM_CS ....no such
[    0.410000] DEV_BOOTCS ....no such
[    0.410000] CRYPT_ENG ....base f0000000, size   2MB
[    0.410000]  Detected Tclk 200000000 and SysClk 500000000
[    0.410000] Synology 6282 DS411slim GPIO Init
[    0.410000] PCIe link is enable, apply PCIe workaround
[    0.910000] PEX0 interface detected Link X4
[    1.410000] PEX1 interface detected no Link.
[    1.410000] PCI: bus0: Fast back to back transfers disabled
[    1.410000] PCI: bus1: Fast back to back transfers enabled
[    1.420000] bio: create slab <bio-0> at 0
[    1.420000] vgaarb: loaded
[    1.420000] SCSI subsystem initialized
[    1.590000] raid6: int32x1    118 MB/s
[    1.760000] raid6: int32x2    173 MB/s
[    1.930000] raid6: int32x4    169 MB/s
[    2.100000] raid6: int32x8    181 MB/s
[    2.100000] raid6: using algorithm int32x8 (181 MB/s)
[    2.100000] Switching to clocksource kw_clocksource
[    2.100000] NET: Registered protocol family 2
[    2.100000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[    2.100000] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[    2.100000] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[    2.100000] TCP: Hash tables configured (established 8192 bind 8192)
[    2.100000] TCP reno registered
[    2.100000] NET: Registered protocol family 1
[    2.100000] RPC: Registered udp transport module.
[    2.100000] RPC: Registered tcp transport module.
[    2.100000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    2.100000] Trying to unpack rootfs image as initramfs...
[    3.150000] rootfs image is not initramfs (no cpio magic); looks like an initrd
[    3.160000] Freeing initrd memory: 4096K
[    3.170000] XOR registered 4 channels
[    3.170000] XOR 2nd invalidate WA enabled
[    3.170000] VFS: Disk quotas dquot_6.5.2
[    3.170000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    3.170000] msgmni has been set to 486
[    3.170000] alg: No test for md5 (md5-generic)
[    3.170000] alg: No test for des (des-generic)
[    3.170000] alg: No test for des3_ede (des3_ede-generic)
[    3.170000] alg: No test for stdrng (krng)
[    3.170000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[    3.170000] io scheduler noop registered
[    3.170000] io scheduler anticipatory registered (default)
[    3.180000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    3.180000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[    3.190000] console [ttyS0] enabled
[    3.190000] serial8250.1: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A
[    3.210000] brd: module loaded
[    3.210000] sata_mv 0000:00:01.0: version 1.28
[    3.210000] PCI: enabling device 0000:00:01.0 (0140 -> 0143)
[    3.220000] sata_mv 0000:00:01.0: Gen-IIE 32 slots 4 ports SCSI mode IRQ via INTx
[    3.230000] scsi0 : sata_mv
[    3.230000] scsi1 : sata_mv
[    3.230000] scsi2 : sata_mv
[    3.240000] scsi3 : sata_mv
[    3.240000] ata1: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0022000 irq 9
[    3.250000] ata2: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0024000 irq 9
[    3.260000] ata3: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0026000 irq 9
[    3.260000] ata4: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0028000 irq 9
[    3.270000] Enable Synology sata fast booting
[    4.680000] sata_mv sata_mv.0: version 1.28
[    4.680000] sata_mv sata_mv.0: slots 32 ports 2
[    4.690000] scsi4 : sata_mv
[    4.690000] scsi5 : sata_mv
[    4.690000] ata5: SATA max UDMA/133 irq 21
[    4.700000] ata6: SATA max UDMA/133 irq 21
[    4.700000] Enable Synology sata fast booting
[    5.040000] ata1: SATA link down (SStatus 0 SControl 300)
[    5.390000] ata2: SATA link down (SStatus 0 SControl 300)
[    5.400000] physmap platform flash device: 00400000 at f8000000
[    5.400000] SPI Serial flash detected @ 0xf8000000, 4096KB (64sec x 64KB)
[    5.410000] Searching for RedBoot partition table in SYNOMTD-0 at offset 0x3f0000
[    5.430000] 6 RedBoot partitions found on MTD device SYNOMTD-0
[    5.440000] SYNOMTD flash bank 0: Using RedBoot partition definition
[    5.450000] Creating 6 MTD partitions on "SYNOMTD-0":
[    5.450000] 0x000000000000-0x000000080000 : "RedBoot"
[    5.460000] 0x000000080000-0x000000280000 : "zImage"
[    5.460000] 0x000000280000-0x0000003c0000 : "rd.gz"
[    5.470000] 0x0000003c0000-0x0000003d0000 : "vendor"
[    5.470000] vender Mac1 checksum error ucSum:0x00 Buf:0x00 Sum:0.
[    5.480000] vender Mac2 checksum error ucSum:0x00 Buf:0x00 Sum:0.
[    5.490000] vender Mac3 checksum error ucSum:0x00 Buf:0x00 Sum:0.
[    5.490000] serial number='DCH9N00195'
[    5.490000] 0x0000003d0000-0x0000003f0000 : "RedBoot Config"
[    5.500000] 0x0000003f0000-0x000000400000 : "FIS directory"
[    5.510000] SPI Serial flash detected @ 0xf4000000, 4096KB (64sec x 64KB)
[    5.520000] cmdlinepart partition parsing not available
[    5.520000] Loading Marvell Ethernet Driver:
[    5.530000]   o Cached descriptors in DRAM
[    5.530000]   o DRAM SW cache-coherency
[    5.530000]   o 2 Giga ports supported
[    5.540000]   o Single RX Queue support - ETH_DEF_RXQ=0
[    5.540000]   o Single TX Queue support - ETH_DEF_TXQ=0
[    5.550000]   o TCP segmentation offload (TSO) supported
[    5.550000]   o Receive checksum offload supported
[    5.560000]   o Transmit checksum offload supported
[    5.560000]   o SKB Recycle supported - (Enabled)
[    5.570000]   o Rx descripors: q0=128
[    5.570000]   o Tx descripors: q0=532
[    5.580000]   o Loading network interface(s):
[    5.580000]     o  register under mv88fx_eth platform
[    5.590000]     o eth0, ifindex = 2, GbE port = 0
[    5.590000]     o eth0, phy chipid = 1410e40, Support WOL = 0
[    5.600000]
[    5.600000] md: linear personality registered for level -1
[    5.600000] md: raid0 personality registered for level 0
[    5.610000] md: raid1 personality registered for level 1
[    5.620000] md: raid10 personality registered for level 10
[    5.620000] md: raid6 personality registered for level 6
[    5.630000] md: raid5 personality registered for level 5
[    5.630000] md: raid4 personality registered for level 4
[    5.640000] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[    5.650000] cpuidle: using governor ladder
[    5.650000] TCP cubic registered
[    5.650000] NET: Registered protocol family 17
[    5.660000] NET: Registered protocol family 15
[    5.660000] registered taskstats version 1
[    5.790000] ata3: SATA link down (SStatus 0 SControl 300)
[    5.790000] ata5: SATA link down (SStatus 0 SControl F300)
[    6.150000] ata4: SATA link down (SStatus 0 SControl 300)
[    6.500000] ata6: SATA link down (SStatus 0 SControl F300)
[    6.500000] md: Waiting for all devices to be available before autodetect
[    6.510000] md: If you don't use raid, use raid=noautodetect
[    6.510000] md: Autodetecting RAID arrays.
[    6.520000] md: Scanned 0 and added 0 devices.
[    6.520000] md: autorun ...
[    6.520000] md: ... autorun DONE.
[    6.530000] RAMDISK: lzma image found at block 0
[    7.660000] VFS: Mounted root (ext2 filesystem) on device 1:0.
START /linuxrc.syno
Insert basic USB modules...
:: Loading module usbcore[    7.920000] usbcore: registered new interface driver usbfs
[    7.930000] usbcore: registered new interface driver hub
[    7.940000] usbcore: registered new interface driver ethub
[    7.940000] usbcore: registered new device driver usb
 ... [  OK  ]
:: Loading module ehci-hcd[    8.020000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    8.020000] orion-ehci orion-ehci.0: Marvell Orion EHCI
[    8.030000] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
[    8.070000] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[    8.090000] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[    8.090000] usb usb1: configuration #1 chosen from 1 choice
[    8.120000] hub 1-0:1.0: USB hub found
[    8.120000] hub 1-0:1.0: 1 port detected
 ... [  OK  ]
:: Loading module ohci-hcd[    8.230000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
 ... [  OK  ]
:: Loading module xhci-hcd ... [  OK  ]
:: Loading module etxhci-hcd ... [  OK  ]
Insert net driver(Mindspeed only)...
[    8.380000] ds411slim_synobios: module license 'Synology Inc.' taints kernel.
[    8.390000] Disabling lock debugging due to kernel taint
[    8.410000] TWSI: twsiDataReceive ERROR - status 50 in Rd Terminate
[    8.420000] correction with 0x00
[    8.450000] TWSI: twsiDataReceive ERROR - status 50 in Rd Terminate
[    8.520000] 2000-256-0 8:26:0 UTC
[    8.520000] synobios: load, major number 201
[    8.530000] Brand: Synology
[    8.530000] Model: DS-411slim
[    8.530000] This is default settings: set group disks wakeup number to 1, spinup time deno 1
[    8.540000] synobios cpu_arch proc entry initialized
[    8.550000] synobios crypto_hw proc entry initialized
[    8.550000] synobios syno_platform proc entry initialized
[    8.560000] usb 1-1: new high speed USB device using orion-ehci and address 2
Starting /usr/syno/bin/synocfgen...
/usr/syno/bin/synocfgen returns 0
[    8.600000] synobios: unload
Exit on error [1] DISK NOT INSTALLED...
Fri May  7 08:26:00 UTC 2021
sys /sys sysfs rw,relatime 0 0
/dev/root.old / ext2 rw,relatime,errors=continue,user_xattr 0 0
none /dev devtmpfs rw,relatime,size=122604k,nr_inodes=30651,mode=755 0 0
proc /proc proc rw,relatime 0 0
linuxrc.syno failed on 1
starting pid 573, tty '': '/etc/rc'
:: Starting /etc/rc
:: Mounting procfs ... [  OK  ]
:: Mounting tmpfs ... [  OK  ]
:: Mounting devtmpfs ... [  OK  ]
:: Mounting devpts ... [  OK  ]
:: Mounting sysfs ... [  OK  ]
mdadm: error opening /dev/md1: No such file or directory
rc: Use all internal disk as swap.
rc: No internal disk installed.
swapon: can't stat '/dev/md1': No such file or directory
:: Loading module fat ... [  OK  ]
:: Loading module vfat ... [  OK  ]
:: Mounting usbfs ... [  OK  ]
:: Loading module sky2[    9.450000] sky2 driver version 1.25
 ... [  OK  ]
:: Loading module synobios[    9.530000] TWSI: twsiDataReceive ERROR - status 50 in Rd Terminate
[    9.540000] correction with 0x00
[    9.570000] TWSI: twsiDataReceive ERROR - status 50 in Rd Terminate
[    9.640000] 2000-256-0 8:26:0 UTC
[    9.640000] synobios: load, major number 201
[    9.650000] Brand: Synology
[    9.650000] Model: DS-411slim
[    9.650000] This is default settings: set group disks wakeup number to 1, spinup time deno 1
[    9.660000] synobios cpu_arch proc entry initialized
[    9.670000] synobios crypto_hw proc entry initialized
[    9.670000] synobios syno_platform proc entry initialized
 ... [  OK  ]
 
[u] Log (Ethernet cable connected):[/u]
 [code][/code]
cat: can't open '/proc/sys/kernel/syno_skip_vender_mac_interfaces': No such file[    9.900000] eth0: mac address changed
 or directory
[   11.940000] eth0: started
udhcpc (v1.16.1) started
eth0      Link encap:Ethernet  HWaddr 00:50:43:3C:3D:5D
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:532
          RX bytes:0 (0.0   TX bytes:0 (0.0 
          Interrupt:11

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0   TX bytes:0 (0.0 

:: Starting syslogd ... [  OK  ]
 :: Starting scemd


Log (Ethernet cable connected):

Code: Select all

         __  __                      _ _
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
 \___/    |____/ \___/ \___/ \__|  ** LOADER **
 ** MARVELL BOARD: Synology Disk Station LE

U-Boot 1.1.4 (Aug  9 2010 - 19:58:12) Marvell version: 3.5.3

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 0068B3D4

Soc: MV88F6282 Rev 1CPU running @ 1500Mhz L2 running @ 500Mhz
SysClock = 500Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000   size 256MB
DRAM Total size 256MB  16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Using default environment

[4096kB@f8000000] Flash:  4 MB

CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
PEX 1: interface detected no Link.

Synology Model: DS411slim
Fan Status: Good

Net:   egiga0 [PRIME], egiga1
Hit any key to stop autoboot:  0
## Booting image at f8080000 ...
   Image Name:   Linux-2.6.32.12
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1552152 Bytes =  1.5 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK
## Loading Ramdisk Image at f8280000 ...
   Image Name:   synology_88f6282_411slim 8451
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    1030907 Bytes = 1006.7 kB
   Load Address: 00800000
   Entry Point:  00800000
   Verifying Checksum ... OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000] Linux version 2.6.32.12 (root@build4) (gcc version 4.6.4 (Marvell GCC release 20150204-c4af733b 64K MAXPAGESIZE ALIGN CVE-2015-0235) ) #8451 Wed Aug 17 05:12:01 CST 2016
[    0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
[    0.000000] CPU: VIVT data cache, VIVT instruction cache
[    0.000000] Machine: Synology 6282 board
[    0.000000] Using UBoot passing parameters structure
[    0.000000] Sys Clk = 200000000, Tclk = 166666667
[    0.000000] Synology Board ID: 24
[    0.000000] Memory policy: ECC disabled, Data cache writeback
[    0.000000] Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 65024
[    0.000000] Kernel command line: console=ttyS0,115200 ip=off initrd=0x00800040,4M root=/dev/md0 rw syno_hw_version=DS411slimv10 ihd_num=0 netif_num=1
[    0.000000] Synology Hardware Version: DS411slimv10-j
[    0.000000] Internal HD num: 0
[    0.000000] Internal netif num: 1
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Memory: 256MB = 256MB total
[    0.000000] Memory: 244992KB available (3652K code, 519K data, 124K init, 0K highmem)
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:128
[    0.000000] Console: colour dummy device 80x30
[    0.000000] Calibrating delay loop... 1490.94 BogoMIPS (lpj=7454720)
[    0.240000] Mount-cache hash table entries: 512
[    0.240000] CPU: Testing write buffer coherency: ok
[    0.240000] devtmpfs: initialized
[    0.240000] xor: measuring software checksum speed
[    0.290000]    arm4regs  :  1358.000 MB/sec
[    0.340000]    8regs     :   814.800 MB/sec
[    0.390000]    32regs    :  1051.600 MB/sec
[    0.390000] xor: using function: arm4regs (1358.000 MB/sec)
[    0.390000] NET: Registered protocol family 16
[    0.390000] Feroceon L2: Enabling L2
[    0.390000] Feroceon L2: Cache support initialised, in WT override mode.
[    0.410000]
[    0.410000] CPU Interface
[    0.410000] -------------
[    0.410000] SDRAM_CS0 ....base 00000000, size 256MB
[    0.410000] SDRAM_CS1 ....disable
[    0.410000] SDRAM_CS2 ....disable
[    0.410000] SDRAM_CS3 ....disable
[    0.410000] PEX0_MEM ....base e0000000, size 128MB
[    0.410000] PEX0_IO ....base f2000000, size   1MB
[    0.410000] PEX1_MEM ....base e8000000, size 128MB
[    0.410000] PEX1_IO ....base f2100000, size   1MB
[    0.410000] INTER_REGS ....base f1000000, size   1MB
[    0.410000] NFLASH_CS ....base fa000000, size   2MB
[    0.410000] SPI_CS ....base f4000000, size  16MB
[    0.410000] BOOT_ROM_CS ....no such
[    0.410000] DEV_BOOTCS ....no such
[    0.410000] CRYPT_ENG ....base f0000000, size   2MB
[    0.410000]  Detected Tclk 200000000 and SysClk 500000000
[    0.410000] Synology 6282 DS411slim GPIO Init
[    0.410000] PCIe link is enable, apply PCIe workaround
[    0.910000] PEX0 interface detected Link X4
[    1.410000] PEX1 interface detected no Link.
[    1.410000] PCI: bus0: Fast back to back transfers disabled
[    1.410000] PCI: bus1: Fast back to back transfers enabled
[    1.420000] bio: create slab <bio-0> at 0
[    1.420000] vgaarb: loaded
[    1.420000] SCSI subsystem initialized
[    1.590000] raid6: int32x1    118 MB/s
[    1.760000] raid6: int32x2    173 MB/s
[    1.930000] raid6: int32x4    169 MB/s
[    2.100000] raid6: int32x8    181 MB/s
[    2.100000] raid6: using algorithm int32x8 (181 MB/s)
[    2.100000] Switching to clocksource kw_clocksource
[    2.100000] NET: Registered protocol family 2
[    2.100000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[    2.100000] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[    2.100000] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[    2.100000] TCP: Hash tables configured (established 8192 bind 8192)
[    2.100000] TCP reno registered
[    2.100000] NET: Registered protocol family 1
[    2.100000] RPC: Registered udp transport module.
[    2.100000] RPC: Registered tcp transport module.
[    2.100000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    2.100000] Trying to unpack rootfs image as initramfs...
[    3.150000] rootfs image is not initramfs (no cpio magic); looks like an initrd
[    3.170000] Freeing initrd memory: 4096K
[    3.170000] XOR registered 4 channels
[    3.170000] XOR 2nd invalidate WA enabled
[    3.170000] VFS: Disk quotas dquot_6.5.2
[    3.170000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    3.170000] msgmni has been set to 486
[    3.170000] alg: No test for md5 (md5-generic)
[    3.170000] alg: No test for des (des-generic)
[    3.170000] alg: No test for des3_ede (des3_ede-generic)
[    3.170000] alg: No test for stdrng (krng)
[    3.170000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[    3.170000] io scheduler noop registered
[    3.170000] io scheduler anticipatory registered (default)
[    3.180000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    3.180000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[    3.190000] console [ttyS0] enabled
[    3.190000] serial8250.1: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A
[    3.210000] brd: module loaded
[    3.210000] sata_mv 0000:00:01.0: version 1.28
[    3.210000] PCI: enabling device 0000:00:01.0 (0140 -> 0143)
[    3.220000] sata_mv 0000:00:01.0: Gen-IIE 32 slots 4 ports SCSI mode IRQ via INTx
[    3.230000] scsi0 : sata_mv
[    3.230000] scsi1 : sata_mv
[    3.230000] scsi2 : sata_mv
[    3.240000] scsi3 : sata_mv
[    3.240000] ata1: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0022000 irq 9
[    3.250000] ata2: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0024000 irq 9
[    3.260000] ata3: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0026000 irq 9
[    3.260000] ata4: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0028000 irq 9
[    3.270000] Enable Synology sata fast booting
[    4.680000] sata_mv sata_mv.0: version 1.28
[    4.680000] sata_mv sata_mv.0: slots 32 ports 2
[    4.690000] scsi4 : sata_mv
[    4.690000] scsi5 : sata_mv
[    4.690000] ata5: SATA max UDMA/133 irq 21
[    4.700000] ata6: SATA max UDMA/133 irq 21
[    4.700000] Enable Synology sata fast booting
[    5.040000] ata1: SATA link down (SStatus 0 SControl 300)
[    5.390000] ata2: SATA link down (SStatus 0 SControl 300)
[    5.400000] physmap platform flash device: 00400000 at f8000000
[    5.400000] SPI Serial flash detected @ 0xf8000000, 4096KB (64sec x 64KB)
[    5.410000] Searching for RedBoot partition table in SYNOMTD-0 at offset 0x3f0000
[    5.430000] 6 RedBoot partitions found on MTD device SYNOMTD-0
[    5.440000] SYNOMTD flash bank 0: Using RedBoot partition definition
[    5.450000] Creating 6 MTD partitions on "SYNOMTD-0":
[    5.450000] 0x000000000000-0x000000080000 : "RedBoot"
[    5.460000] 0x000000080000-0x000000280000 : "zImage"
[    5.460000] 0x000000280000-0x0000003c0000 : "rd.gz"
[    5.470000] 0x0000003c0000-0x0000003d0000 : "vendor"
[    5.470000] vender Mac1 checksum error ucSum:0x00 Buf:0x00 Sum:0.
[    5.480000] vender Mac2 checksum error ucSum:0x00 Buf:0x00 Sum:0.
[    5.490000] vender Mac3 checksum error ucSum:0x00 Buf:0x00 Sum:0.
[    5.490000] serial number='DCH9N00195'
[    5.490000] 0x0000003d0000-0x0000003f0000 : "RedBoot Config"
[    5.500000] 0x0000003f0000-0x000000400000 : "FIS directory"
[    5.510000] SPI Serial flash detected @ 0xf4000000, 4096KB (64sec x 64KB)
[    5.520000] cmdlinepart partition parsing not available
[    5.520000] Loading Marvell Ethernet Driver:
[    5.530000]   o Cached descriptors in DRAM
[    5.530000]   o DRAM SW cache-coherency
[    5.530000]   o 2 Giga ports supported
[    5.540000]   o Single RX Queue support - ETH_DEF_RXQ=0
[    5.540000]   o Single TX Queue support - ETH_DEF_TXQ=0
[    5.550000]   o TCP segmentation offload (TSO) supported
[    5.550000]   o Receive checksum offload supported
[    5.560000]   o Transmit checksum offload supported
[    5.560000]   o SKB Recycle supported - (Enabled)
[    5.570000]   o Rx descripors: q0=128
[    5.570000]   o Tx descripors: q0=532
[    5.580000]   o Loading network interface(s):
[    5.580000]     o  register under mv88fx_eth platform
[    5.590000]     o eth0, ifindex = 2, GbE port = 0
[    5.590000]     o eth0, phy chipid = 1410e40, Support WOL = 0
[    5.600000]
[    5.600000] md: linear personality registered for level -1
[    5.600000] md: raid0 personality registered for level 0
[    5.610000] md: raid1 personality registered for level 1
[    5.620000] md: raid10 personality registered for level 10
[    5.620000] md: raid6 personality registered for level 6
[    5.630000] md: raid5 personality registered for level 5
[    5.630000] md: raid4 personality registered for level 4
[    5.640000] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[    5.650000] cpuidle: using governor ladder
[    5.650000] TCP cubic registered
[    5.650000] NET: Registered protocol family 17
[    5.660000] NET: Registered protocol family 15
[    5.660000] registered taskstats version 1
[    5.790000] ata3: SATA link down (SStatus 0 SControl 300)
[    5.790000] ata5: SATA link down (SStatus 0 SControl F300)
[    6.150000] ata4: SATA link down (SStatus 0 SControl 300)
[    6.500000] ata6: SATA link down (SStatus 0 SControl F300)
[    6.500000] md: Waiting for all devices to be available before autodetect
[    6.510000] md: If you don't use raid, use raid=noautodetect
[    6.510000] md: Autodetecting RAID arrays.
[    6.520000] md: Scanned 0 and added 0 devices.
[    6.520000] md: autorun ...
[    6.520000] md: ... autorun DONE.
[    6.530000] RAMDISK: lzma image found at block 0
[    7.660000] VFS: Mounted root (ext2 filesystem) on device 1:0.
START /linuxrc.syno
Insert basic USB modules...
:: Loading module usbcore[    7.920000] usbcore: registered new interface driver usbfs
[    7.920000] usbcore: registered new interface driver hub
[    7.950000] usbcore: registered new interface driver ethub
[    7.950000] usbcore: registered new device driver usb
 ... [  OK  ]
:: Loading module ehci-hcd[    8.020000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    8.020000] orion-ehci orion-ehci.0: Marvell Orion EHCI
[    8.030000] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
[    8.070000] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[    8.090000] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[    8.090000] usb usb1: configuration #1 chosen from 1 choice
[    8.120000] hub 1-0:1.0: USB hub found
[    8.120000] hub 1-0:1.0: 1 port detected
 ... [  OK  ]
:: Loading module ohci-hcd[    8.230000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
 ... [  OK  ]
:: Loading module xhci-hcd ... [  OK  ]
:: Loading module etxhci-hcd ... [  OK  ]
Insert net driver(Mindspeed only)...
[    8.380000] ds411slim_synobios: module license 'Synology Inc.' taints kernel.
[    8.390000] Disabling lock debugging due to kernel taint
[    8.410000] TWSI: twsiDataReceive ERROR - status 50 in Rd Terminate
[    8.420000] correction with 0x00
[    8.450000] TWSI: twsiDataReceive ERROR - status 50 in Rd Terminate
[    8.520000] 2000-256-0 8:30:0 UTC
[    8.520000] synobios: load, major number 201
[    8.530000] Brand: Synology
[    8.530000] Model: DS-411slim
[    8.530000] This is default settings: set group disks wakeup number to 1, spinup time deno 1
[    8.540000] synobios cpu_arch proc entry initialized
[    8.550000] synobios crypto_hw proc entry initialized
[    8.550000] synobios syno_platform proc entry initialized
[    8.560000] usb 1-1: new high speed USB device using orion-ehci and address 2
Starting /usr/syno/bin/synocfgen...
/usr/syno/bin/synocfgen returns 0
[    8.600000] synobios: unload
Exit on error [1] DISK NOT INSTALLED...
Fri May  7 08:30:00 UTC 2021
sys /sys sysfs rw,relatime 0 0
/dev/root.old / ext2 rw,relatime,errors=continue,user_xattr 0 0
none /dev devtmpfs rw,relatime,size=122604k,nr_inodes=30651,mode=755 0 0
proc /proc proc rw,relatime 0 0
linuxrc.syno failed on 1
starting pid 573, tty '': '/etc/rc'
:: Starting /etc/rc
:: Mounting procfs ... [  OK  ]
:: Mounting tmpfs ... [  OK  ]
:: Mounting devtmpfs ... [  OK  ]
:: Mounting devpts ... [  OK  ]
:: Mounting sysfs ... [  OK  ]
mdadm: error opening /dev/md1: No such file or directory
rc: Use all internal disk as swap.
rc: No internal disk installed.
swapon: can't stat '/dev/md1': No such file or directory
:: Loading module fat ... [  OK  ]
:: Loading module vfat ... [  OK  ]
:: Mounting usbfs ... [  OK  ]
:: Loading module sky2[    9.450000] sky2 driver version 1.25
 ... [  OK  ]
:: Loading module synobios[    9.530000] TWSI: twsiDataReceive ERROR - status 50 in Rd Terminate
[    9.540000] correction with 0x00
[    9.570000] TWSI: twsiDataReceive ERROR - status 50 in Rd Terminate
[    9.640000] 2000-256-0 8:30:0 UTC
[    9.640000] synobios: load, major number 201
[    9.650000] Brand: Synology
[    9.650000] Model: DS-411slim
[    9.650000] This is default settings: set group disks wakeup number to 1, spinup time deno 1
[    9.660000] synobios cpu_arch proc entry initialized
[    9.660000] synobios crypto_hw proc entry initialized
[    9.670000] synobios syno_platform proc entry initialized
 ... [  OK  ]
cat: can't open '/proc/sys/kernel/syno_skip_vender_mac_interfaces': No such file[    9.900000] eth0: mac address changed
 or directory
[   12.940000] ethPort_0: TIMEOUT for TX stoped !!! txQueueCmd - 0x08101
[   12.940000] eth0: link down
[   12.950000] eth0: started
udhcpc (v1.16.1) started
 [   13.060000] eth0: link up, full duplex, speed 1 Gbps


I worry about the record:

Code: Select all

cat: can't open '/proc/sys/kernel/syno_skip_vender_mac_interfaces': No such file[ 9.900000] eth0: mac address changed or directory
[ 12.940000] ethPort_0: TIMEOUT for TX stoped !!! txQueueCmd - 0x08101[ 12.950000] eth0: link down


At this moment I had change Ether chip 88e1116r and GST5009LF transformer but steel not work :(
In terminal log I can see linkUp1 Gb but no communication.
U20 flash has soldering track, so, I worry about dump is NOT NATIVE.
Confirmation - MAC on label and in log is NOT SAME. Maybe, from wrong HW revision.

So, I try use TFTP. (unpack DSM_DS411slim_15047.pat, rename "zImage" to C0A8019A.img, set 192.168.1.155 at TFTP server)
TFTP try:

Code: Select all

         __  __                      _ _
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
 \___/    |____/ \___/ \___/ \__|  ** LOADER **
 ** MARVELL BOARD: Synology Disk Station LE

U-Boot 1.1.4 (Aug  9 2010 - 19:58:12) Marvell version: 3.5.3

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 0068B3D4

Soc: MV88F6282 Rev 1CPU running @ 1500Mhz L2 running @ 500Mhz
SysClock = 500Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000   size 256MB
DRAM Total size 256MB  16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Using default environment

[4096kB@f8000000] Flash:  4 MB

CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
PEX 1: interface detected no Link.

Synology Model: DS411slim
Fan Status: Good

Net:   egiga0 [PRIME], egiga1
Hit any key to stop autoboot:  0
Marvell>> printenv
bootcmd=bootm F8080000 F8280000
baudrate=115200
loads_echo=0
ipaddr=192.168.1.154
serverip=192.168.1.155
rootpath=/mnt/ARM_FS/
netmask=255.255.254.0
run_diag=yes
stdin=serial
stdout=serial
stderr=serial
console=console=ttyS0,115200 mtdparts=spi_flash:0x80000@0(uboot)ro,0x300000@0x100000(root)
mainlineLinux=no
CASset=min
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
MALLOC_len=1
ethprime=egiga0
netbsd_en=no
vxworks_en=no
bootargs_root=root=/dev/nfs rw
bootargs_end=:::DB88FXX81:eth0:none
image_name=uImage
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000;
lcd0_enable=0
lcd0_params=640x480-16@60
lcd0_bootargs=video-dovefb:lcd0:$(lcd0_params) clcd.lcd0_enable=$(lcd0_enable)
bootdelay=3
disaMvPnp=no
ethaddr=00:50:43:3c:3b:5d
ethmtu=1500
mvPhoneConfig=mv_phone_config=dev[0]:fxs,dev[1]:fxo
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
usb0Mode=host
pcieTune=no
bootargs=console=ttyS0,115200 ip=off initrd=0x00800040,4M root=/dev/md0 rw syno_hw_version=DS411slimv10 ihd_num=0 netif_num=1
ethact=egiga0

Environment size: 1241/4092 bytes
Marvell>> tftpboot
*** Warning: no boot file name; using 'C0A8019A.img'
Using egiga0 device
TFTP from server 192.168.1.155; our IP address is 192.168.1.154
Filename 'C0A8019A.img'.
Load address: 0x800000
Loading: *


Try memtest in terminal:

Code: Select all

         __  __                      _ _
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
 \___/    |____/ \___/ \___/ \__|  ** LOADER **
 ** MARVELL BOARD: Synology Disk Station LE

U-Boot 1.1.4 (Aug  9 2010 - 19:58:12) Marvell version: 3.5.3

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 0068B3D4

Soc: MV88F6282 Rev 1CPU running @ 1500Mhz L2 running @ 500Mhz
SysClock = 500Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000   size 256MB
DRAM Total size 256MB  16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Using default environment

[4096kB@f8000000] Flash:  4 MB

CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
PEX 1: interface detected no Link.

Synology Model: DS411slim
Fan Status: Good

Net:   egiga0 [PRIME], egiga1
Hit any key to stop autoboot:  0
Marvell>> mtest
Pattern 00000000  Writing...


* All logs are full. Means, nothing new in log after long waiting.

I can reed - write U20 (ST M25P32 flash), on external programmer.
Can some check is my flash dump compatible for my NAS HW? (4 mb. where send it?).

Can Some one share proper Dump? Or manual, how to build it (like here:https://forum.synology.com/enu/viewtopic.php?t=84141)?
In case NS411slim flash is 4 MB, so another addresing, And no uboot_*** in unpacked *.PAT

Pleas, help me understand, I got SW or HW problem?
If it`s HW, then where? Ether led shows activity, PC (and NAS log) shows link UP. Ether chip and transformer is new. But no any communication...
All logs ands like device hangs, so, maybe, RAM problem? But, how then Uboot starts, unpack linux image, all checksum is Ok, kernel starts???

Thanks for advice.
* I had wrote to support, but answer is like "Fap cabel few time, push the button, jump around and buy new device" :(
RussH
I'm New!
I'm New!
Posts: 5
Joined: Thu Aug 18, 2016 10:27 am

Re: DS411slim Ethernet prob or hang? Flash Dump?

Postby RussH » Tue Oct 17, 2017 2:28 pm

Hey there, looks like you're further along this route than I am -

I get the following from mine;
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** LOADER **
** MARVELL BOARD: Synology Disk Station LE

U-Boot 1.1.4 (Aug 9 2010 - 19:58:12) Marvell version: 3.5.3

U-Boot code: 00600000 -> 0067FFF0 BSS: -> 0068B3D4

Soc: 88F6282 A0CPU running @ 1600Mhz L2 running @ 533Mhz
SysClock = 533Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Using default environment

[4096kB@f8000000] Flash: 4 MB

CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
PEX 1: interface detected no Link.

Synology Model: DS411slim
Fan Status: Good

Net: egiga0 [PRIME], egiga1
Hit any key to stop autoboot: 0
## Booting image at f8080000 ...
Image Name: Linux-2.6.32.12
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1551524 Bytes = 1.5 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at f8280000 ...
Bad Magic Number▒▒
RussH
I'm New!
I'm New!
Posts: 5
Joined: Thu Aug 18, 2016 10:27 am

Re: DS411slim Ethernet prob or hang? Flash Dump?

Postby RussH » Tue Oct 17, 2017 5:26 pm

actually, you can probably follow this post;

https://www.conetix.com.au/blog/synolog ... m-recovery

Return to “System Managment Mods”

Who is online

Users browsing this forum: No registered users and 2 guests